nazgul:clean

Nazgul Clean

Examples

• /nazgul:clean — Fully remove Nazgul from this project (with confirmation)
• /nazgul:clean --force — Remove without confirmation prompt

Arguments

$ARGUMENTS

Current State

• Nazgul initialized: !test -f nazgul/config.json && echo "YES" || echo "NO"
• Install mode: !test -f nazgul/config.json && jq -r '.install_mode // "shared"' nazgul/config.json 2>/dev/null || echo "unknown"
• Tasks count: !ls nazgul/tasks/TASK-*.md 2>/dev/null | wc -l | tr -d ' '
• Generated agents: !ls .claude/agents/generated/*.md 2>/dev/null | wc -l | tr -d ' '
• CLAUDE.md has nazgul section: !grep -q "Nazgul Framework" CLAUDE.md 2>/dev/null && echo "YES" || echo "NO"
• Gitignore has nazgul entries: !grep -qE "# Nazgul Framework (\(local mode\)|— ephemeral runtime)" .gitignore 2>/dev/null && echo "YES" || echo "NO"

Instructions

Pre-load: Run ToolSearch with query select:AskUserQuestion to load the interactive prompt tool (deferred by default). Do this BEFORE any step that uses AskUserQuestion.

Fully remove Nazgul from this project. No archiving — permanent deletion.

Step 1: Check if Nazgul is Present

If none of the current state indicators show Nazgul presence (no config, no agents, no MCP entry, no CLAUDE.md section):

• Output: "Nazgul is not installed in this project. Nothing to clean."
• Stop here.

Step 2: Parse Arguments

Check $ARGUMENTS for --force flag. If present, skip confirmation.

Step 3: Confirm with User

Unless --force is present, show what will be removed, then use AskUserQuestion to confirm:

First, display a summary of what exists:

Nazgul Clean — Full Removal
═══════════════════════════════════════════════════════

The following will be PERMANENTLY DELETED:

  nazgul/                        [EXISTS | not found]
  .claude/agents/generated/     [N file(s) | not found]
  .claude/settings.json entries [EXISTS | not found]
  CLAUDE.md nazgul section       [EXISTS | not found]
  .gitignore nazgul entries      [EXISTS | not found]

Then use AskUserQuestion:

• header: "Confirm"
• question: "This cannot be undone. Remove all Nazgul files from this project?"
• options:
  • "Remove everything" — "Permanently delete all Nazgul runtime state, agents, and config"
  • "Abort" — "Cancel and keep everything as-is"

If Abort: stop immediately.

Step 4: Remove Runtime State

Delete the entire nazgul/ directory:

rm -rf nazgul/

Step 5: Remove Generated Agents

Delete the .claude/agents/generated/ directory (these are Nazgul-generated reviewer agents):

rm -rf .claude/agents/generated/

If .claude/agents/ is now empty, remove it too. Do NOT remove .claude/ itself as it may contain other settings.

Step 6: Clean .claude/settings.json

If .claude/settings.json exists:

1. Read the file
2. Remove enableAgentTeams key if set to true
3. Use jq:

   jq 'del(.enableAgentTeams)' .claude/settings.json > .claude/settings.json.tmp && mv .claude/settings.json.tmp .claude/settings.json
   

4. If the file is now effectively empty ({} or only has empty arrays), delete it
5. If .claude/ directory is now empty, remove it too. But be careful — check first.

Step 7: Clean CLAUDE.md

If the project's CLAUDE.md contains a Nazgul-injected section:

1. Read CLAUDE.md
2. Look for the Nazgul section — it starts with # Nazgul Framework — Project Instructions (the content from templates/CLAUDE.md.template)
3. Remove everything from that header to the end of the Nazgul section. The Nazgul section runs from # Nazgul Framework — Project Instructions to the end of the file (it is always appended at the bottom by /nazgul:init).
4. Trim any trailing blank lines left behind
5. If CLAUDE.md is now empty (only whitespace), delete the file entirely
6. If CLAUDE.md still has non-Nazgul content, write it back with the Nazgul section removed

Step 8: Clean .gitignore

/nazgul:init writes one of two blocks depending on install mode. Remove whichever is present (both, if somehow both exist):

1. Read .gitignore
2. Remove the local-mode block if present: the marker # Nazgul Framework (local mode) and its lines (nazgul/, .claude/agents/generated/, .mcp.json)
3. Remove the shared-mode ephemeral block if present: the marker # Nazgul Framework — ephemeral runtime and its lines (nazgul/checkpoints/, nazgul/logs/, nazgul/sessions/, nazgul/.session_id, nazgul/.compaction_count, nazgul/archive/, nazgul/reviews/*/test-failures.md, nazgul/reviews/*/simplify-report.md, nazgul/reviews/post-loop-simplify-report.md)
4. Trim any extra blank lines left behind
5. If .gitignore is now empty, delete it
6. Otherwise write it back

Step 9: Output Summary

Nazgul Clean Complete
═══════════════════════════════════════════════════════

Removed:
  nazgul/                        [DELETED | was not present]
  .claude/agents/generated/     [DELETED (N files) | was not present]
  .claude/settings.json entries [CLEANED | was not present]
  CLAUDE.md nazgul section       [REMOVED | was not present]
  .gitignore nazgul entries      [REMOVED | was not present]

Nazgul has been fully removed from this project.
To reinstall: /nazgul:init