ato-language

The ato language

ato is a declarative, constraint-based DSL for describing electronic circuits. There is no control flow, no mutation, and no execution order — you declare what a circuit is, and the compiler + solver resolve it into a valid design.

Quick Start

A minimal complete .ato file:

#pragma experiment("BRIDGE_CONNECT")

import Resistor
import ElectricPower
import Capacitor

module PowerFilter:
    """A simple decoupled power input with a pull-down resistor."""
    power = new ElectricPower
    decoupling_capacitor = new Capacitor
    pulldown_resistor = new Resistor

    power.hv ~> decoupling_capacitor ~> power.lv
    power.hv ~> pulldown_resistor ~> power.lv

    decoupling_capacitor.capacitance = 100nF +/- 20%
    pulldown_resistor.resistance = 100kohm +/- 5%
    assert power.voltage within 3.0V to 3.6V

Validate with ato build from the package directory.

Core Concepts

1. Everything is a Node in a Graph

Every entity (a resistor, a power rail, an I2C bus, a voltage parameter) is a node in a typed graph. Nodes relate to each other through edges: composition (parent–child), connection (same-net), and traits (behavioral metadata). The .ato language is a surface syntax for constructing this graph declaratively.

2. Three Block Types

ato has exactly three ways to define a new type:

Keyword	Semantics	Typical Use
module	A design unit that contains children and connections	Circuit blocks, subsystems
interface	A connectable boundary; can be wired with ~	Buses, power rails, signals
component	A physical part with footprint/symbol	Vendor ICs, connectors

All three compile to graph nodes. The distinction controls which traits the compiler attaches (is_module, is_interface) and what operations are legal (by convention, interfaces appear on both sides of ~).

Inheritance uses from:

module MyRegulator from Regulator:
    pass

3. Composition — Children and Instantiation

Types contain children. Inside a block body, new instantiates a child:

module Board:
    power = new ElectricPower      # interface child
    sensor = new BME280            # module child
    caps = new Capacitor[4]        # array of 4 capacitors

Children are accessed via dot-notation: sensor.power.voltage, caps[0].capacitance.

4. Connection — Declaring Electrical Identity

The wire operator ~ declares that two interfaces are the same net/bus. It is bidirectional and requires matching types:

power_3v3 ~ sensor.power          # ElectricPower ~ ElectricPower
i2c_bus ~ sensor.i2c              # I2C ~ I2C

The bridge operator ~> (requires #pragma experiment("BRIDGE_CONNECT")) inserts a component in series. The component must carry the can_bridge trait which defines its in/out mapping:

power_5v ~> regulator ~> power_3v3
i2c.scl.line ~> pullup ~> power.hv

5. Constraints — Physical Quantities and Assertions

Values in ato carry units and tolerances. The solver uses these to select real parts.

Assignment binds a value to a parameter:

power.voltage = 3.3V +/- 5%
resistor.resistance = 10kohm +/- 10%
i2c.frequency = 400kHz
i2c.address = 0x48

Assertions declare constraints the solver must satisfy:

assert power.voltage within 3.0V to 3.6V
assert i2c.frequency <= 400kHz
assert sensor.i2c.address is 0x50

Three value forms exist:

• Exact: 3.3V
• Bilateral tolerance: 10kohm +/- 5%
• Bounded range: 3.0V to 3.6V

6. Traits — Behavioral Metadata

Traits attach capabilities or metadata to nodes. They are not children — they use trait edges in the graph.

#pragma experiment("TRAITS")

import has_part_removed
import is_atomic_part

module Placeholder:
    trait has_part_removed          # mark as non-physical placeholder
    trait is_atomic_part            # user-defined part with footprint

Key built-in traits:

Trait	Effect
can_bridge	Enables use with ~> operator (defines in/out pin mapping)
has_part_removed	No physical part placed (symbolic node)
is_atomic_part	User-defined part with manufacturer, partnumber, footprint
has_datasheet	Attaches a datasheet reference
has_designator_prefix	Sets PCB designator (R, C, U, etc.)

7. Import System

Bare imports resolve to standard library types (1 line per import):

import ElectricPower
import I2C
import Resistor

Path imports resolve to types defined in other .ato files (1 line per import):

from "atopile/vendor-part/vendor-part.ato" import Vendor_Part

8. Pragma Feature Flags

Experimental syntax is gated behind pragmas (file top, before imports):

#pragma experiment("BRIDGE_CONNECT")     # ~> operator
#pragma experiment("FOR_LOOP")           # for loops
#pragma experiment("TRAITS")             # trait keyword
#pragma experiment("MODULE_TEMPLATING")  # new Foo<p=v>
#pragma experiment("INSTANCE_TRAITS")    # traits on instances

Using gated syntax without the pragma is a compile error.

Statement Reference

Every statement inside a block body is one of:

Statement	Syntax	Purpose
assign	name = value or name = new Type	Bind a value or instantiate a child
connect	a ~ b	Wire two interfaces together
bridge	a ~> b ~> c	Insert bridgeable components in series
assert	assert expr <op> expr	Declare a constraint
retype	name -> NewType	Replace an inherited child's type
pin	pin VCC	Declare a physical pin
signal	signal reset	Declare an electrical signal
trait	trait TraitName	Attach a trait
import	import Type	Import a type
for	for x in arr:	Iterate over an array (pragma-gated)
string	"""..."""	Documentation string
pass	pass	Empty placeholder

Statements within a block are order-independent — the compiler resolves the full graph, not a sequence of operations.

Type System

Interfaces (connectable with ~ or ~>)

Type	Children / Parameters	Purpose
Electrical	(single node)	Raw electrical connection point
ElectricPower	.hv, .lv (Electrical); .voltage, .max_current	Power rails
ElectricLogic	.line (Electrical), .reference (ElectricPower)	Digital signals with voltage context
ElectricSignal	.line (Electrical), .reference (ElectricPower)	Analog signals
I2C	.scl, .sda (ElectricLogic); .frequency, .address	I2C bus
SPI	.sclk, .mosi, .miso (ElectricLogic); .frequency	SPI bus
UART / UART_Base	.tx, .rx (ElectricLogic); flow control lines	Serial
I2S	audio data bus lines	Digital audio
DifferentialPair	.p, .n	Differential signals
USB2_0 / USB3 / USB2_0_IF	USB data + power	USB interfaces
CAN_TTL	CAN bus lines	CAN bus
SWD / JTAG	debug lines	Debug interfaces
Ethernet / HDMI / RS232 / PDM / XtalIF / MultiSPI	protocol-specific	Other protocols

Modules (instantiable with new)

Type	Children / Parameters	Designator
Resistor	.unnamed[0..1]; .resistance, .max_power	R
Capacitor	.unnamed[0..1], .power; .capacitance, .max_voltage, .temperature_coefficient	C
CapacitorPolarized	polarized variant of Capacitor	C
Inductor	.unnamed[0..1]; .inductance	L
Fuse	.unnamed[0..1]; .trip_current, .fuse_type	F
Diode	.anode, .cathode; .forward_voltage, .current	D
LED	.diode; .brightness, .color	D
MOSFET	.source, .gate, .drain; .channel_type, .gate_source_threshold_voltage	Q
BJT	.emitter, .base, .collector; .doping_type	Q
Regulator / AdjustableRegulator	.power_in, .power_out	—
Crystal	.unnamed[0..1], .gnd; .frequency, .load_capacitance	XTAL
Crystal_Oscillator	oscillator module	—
ResistorVoltageDivider	voltage divider circuit	—
FilterElectricalRC	RC filter	—
Net	.part_of (Electrical)	—
TestPoint	.contact; .pad_size, .pad_type	TP
MountingHole / NetTie	mechanical	—
SPIFlash	SPI flash memory	—

Traits (attachable with trait)

has_part_removed, is_atomic_part, can_bridge, can_bridge_by_name, has_datasheet, has_designator_prefix, has_doc_string, has_net_name_affix, has_net_name_suggestion, has_package_requirements, has_single_electric_reference, is_auto_generated, requires_external_usage

Units and Literals

SI-prefixed units: V, mV | A, mA | ohm, kohm, Mohm | F, uF, nF, pF | Hz, kHz, MHz, GHz | s, ms | W, mW

Number formats: decimal (3.3), scientific (1e-6), hex (0x48), binary (0b1010), underscore-separated (1_000_000)

Booleans: True, False

Invariants

1. Type-safe connections: ~ and ~> should connect matching interface types. ElectricPower ~ I2C is a type mismatch (enforcement is being strengthened).
2. Pragma gates syntax: using ~>, for, trait, or <> without the matching pragma is a compile error.
3. Tolerances on passives: resistance = 10kohm (zero tolerance) matches no real parts. Always use +/- N%.
4. ElectricLogic needs a reference: logic signals require a power reference for voltage context. Set signal.reference ~ power_rail.
5. Order independence: statements within a block are not sequentially executed. The solver resolves the full graph.
6. No procedural logic: no if, while, return, functions, classes, or exceptions.